matplace
Tools

Headband with horns, ears or a crown

A headband sized to the head with a decoration on top: devil horns, cat or bunny ears, reindeer antlers, a crown, a halo or a unicorn.

Input

Decoration
Start from a preset

Size

Who it is for
How the decoration is held
Size
44–64 cm

Measure with a tape across the forehead and above the ears. The band comes out a little narrower than the head, so that it holds.

8–25 mm
2–4 mm

A thinner band is softer and opens further, a thicker one presses more. 2.6 mm holds in PETG and in PLA.

60–160 %
30–140 mm
-30–30 °
Wall thickness and more

Colours

Material and quantity

Sizes and parts appear with the preview.

On the next page you pick the colour, the material and the print settings and ask for the price. Nothing is ordered or paid yet.

It prints without supports: the band lies on its side, so the layers run along the arc and take the bending. The decoration prints flat beside it in its own colour and is pushed from the front into a pocket on the band; a drop of superglue fixes it for good. Choose PETG for the band, it springs better than PLA.

Made-to-measure headband with horns, ears, antlers or a crown

The tool makes a headband for a head circumference from 44 to 64 cm: for a small child, a schoolchild or an adult. On top goes the decoration you pick: devil horns, cat or bunny ears, reindeer antlers, a crown, an angel's halo or a unicorn. You set the size of the decoration, the spacing, the lean, the width of the band from 8 to 25 mm and its thickness.

The band is printed on its side without supports, so the layers run along the arc and the band takes the bending when it is put on. The decoration is a flat part of its own in its own colour: it prints beside the band and is pushed from the front into a pocket, where a dovetail holds it. For a single piece choose the one-piece version in one colour. Small teeth inside, above the ears, keep the band from slipping.

How it works

  1. Measure the head. With a tape across the forehead and above the ears. A preset will do too: a child of 3 to 6, a schoolchild, an adult.
  2. Pick the decoration. Horns, cat ears, bunny ears, antlers, a crown, a halo or a unicorn. The preview redraws at once.
  3. Tune the size and the colours. The size of the decoration, the spacing and the lean are sliders. The band and the decoration can each have a colour of their own.
  4. Order the print, or download. Next to the preview you see the dimensions and a rough price. You choose the material when you order; the model and the slicer project are free to download.

What the tool can make

A child's headband for a 52 cm head with red devil horns.
A child's headband for a 52 cm head with red devil horns.
A black headband with cat ears for a schoolchild, head 54 cm.
A black headband with cat ears for a schoolchild, head 54 cm.
An adult's headband with reindeer antlers for a Christmas party.
An adult's headband with reindeer antlers for a Christmas party.

Common questions

What material should the headband be made of?

We recommend PETG: it is tough, it springs and it takes bending better than PLA. PLA holds at the default thickness of 2.6 mm too, but it is more brittle; dropped on the floor or in the frost it cracks sooner. The decoration can be PLA without worry, it does not bend.

How do I find the right size?

Measure the head across the forehead and above the ears. Children in nursery school are around 50 to 52 cm, schoolchildren about 54 cm, adults 55 to 59 cm. The band comes out a little narrower than the head so that it holds, and both ends are rounded and thinned so that they do not press behind the ears.

Does the decoration hold on the band by itself?

The decoration has a dovetail tongue that is pushed from the front into a pocket on the band; it cannot be pulled out upwards. The play is two tenths of a millimetre a side and can be changed. For children we recommend a drop of superglue, then the decoration holds for good.

Can the decoration have a different colour than the band?

Yes. In the version "separate, in a pocket" the band and the decoration are two parts and each prints from its own filament: a black band with red horns, a white one with a golden halo. The one-piece version is a single piece in one colour.

Does the print need supports?

No. The band lies on its side and the decoration flat, nothing hangs in the air. A child's headband with horns fits a 250 × 250 mm bed with the decoration inside the arc.

Can one band take several decorations?

Yes. Horns, cat ears, bunny ears and antlers share the same tongue, and with the same spacing and the same head size they fit the same two pockets: print one band and swap the decorations as long as you do not glue them. The crown, the halo and the unicorn have their pockets elsewhere and need a band of their own.

Where next

Looking for something else? See all Tools